Read the Progressive Dairyman Canada digital edition
advertisement

Not all manure is conveyed equally

Andrew Wedel Published on 20 July 2012

Not all manure is conveyed equally, so to speak, because not all manure is subjected to the same environmental conditions after being “deposited” on the alley floor.

One of those conditions is bedding, especially where sand bedding is concerned. Whereas non-sand-laden manure can be conveyed using gravity flow in large-diameter, flat pipes or stirred up and pumped long distances using centrifugal pumps, sand-laden manure cannot reliably over the long term.

advertisement

advertisement

Several factors go into selecting a manure conveyance system – for example, site topography, building layout, climate and management style. And there’s more.

What will be the ultimate fate of the manure – manure storage, digester, irrigation, etc.? Can the downstream storage or treatment process tolerate dilution?

Selecting conveyance systems for manure containing sand requires, first, an understanding of all of the site-specific factors, in addition to the physical characteristics of sand-laden manure (SLM).

Sand usage in freestalls averages around 50 pounds per cow per day, give or take. Adding this much sand (a stackable material) to manure (a flowable product), the result is a material that is neither stackable nor flowable.

Being a non-flowable material, gravity flow conveyance of undiluted SLM is not recommended under any circumstances, even in short runs of large-diameter pipes. High friction and low velocity under these circumstances ultimately results in clogging.

advertisement

There are surely examples (albeit fleeting) of success with these kinds of systems; however, it is in cases where either producers are cleaning the “gravity” flow gutter with a skid loader-mounted implement and/or sand usage is low – somewhere in the 30 pounds per cow per day range.

Under no circumstances is this low level of sand usage recommended for the sake of “fixing” a failed SLM system at the great expense of cow health.

Whereas gravity conveyance of undiluted SLM is a non-starter, gravity conveyance of diluted SLM is a very viable option using flush flumes.

Flumes are used in one of two ways. The first is to convey diluted SLM from flush alleys. The second is where a combination of hydraulic energy derived from pumped lagoon water and pipe slope, also a source of energy, is used to dilute and keep scraped SLM moving, or scoured, in a pipe usually 24 inches in diameter.

As engineers, we are often asked the question: “How many gpm does it take to convey sand-laden manure?” The answer is the typical engineer’s response: “It depends.”

Seriously, it depends. It depends on whether or not dilution is present, site elevation, pipe diameter, to name a few factors. The viability of flume systems is most often limited only by site elevation or quality of the water doing the conveying.

advertisement

In some situations, whether a site is incompatible with fluming, flume water isn’t available, downstream processes potentially incompatible with dilution, etc., SLM is conveyed without the addition of dilution water, and without relying on gravity, using auger systems.

Augers used with SLM rely on design characteristics common to the mining industries. For long life, materials of construction must be harder than the sand grains being conveyed and rotational speeds are kept to a minimum.

Also, the clearance between the moving auger flighting and concrete trough is one inch, minimum, in order to reduce abrasive wear.

Augers are placed at the same locations as flumes – either through the centre or at the end of barns – and discharge at a reception tank or manure storage. Auger lengths and power requirements vary. Multiple augers can be placed in series to achieve any length desired.

The challenge, however, becomes (with multiple augers) placement of the drive units so as not to interfere with cow movement and manure scraping.

Four augers placed in series to achieve lengths in excess of 700 feet is achievable. With augers, safety is paramount. Top covers and grates must be maintained for the entire auger length.

Vacuum (vac) tanks, as the name implies, are manure tankers equipped with a vacuum arrangement that “suck” manure off the alley floor and into the tank.

Manure can then be transported to the desired location. Vac tanks have found favour in situations where flumes and augers are not options due to facility layout and/or site topography.

Vac tanks have proven particularly useful on large facilities where manure must be conveyed from multiple barns over a large area to one location for processing, say, an anaerobic digester.

Vac tanks have also been useful where facilities have converted from non-sand bedding to sand – that is, where an existing manure conveyance system like gravity flow is incompatible with sand or where SLM conveyance systems have failed.

Vac tanks are large and heavy implements that are either truck-mounted or trailer-mounted. Due to high axle loads, concrete placed over inadequate subgrade is subject to cracking. A skilled tractor operator is required to successfully maneuver a vac tank around a dairy.

When purchasing vac tanks, opt for features that reduce or eliminate sand buildup in the tanks. This may be augers, agitators or a combination of the two.

Vac tanks are so integral to a manure-handling program that two units should be considered in order to manage around breakdowns, maintenance and freezing.

Remember to use systems specifically designed for sand-laden manure where sand bedding is used. The most common reason for SLM handling system failure is not taking into consideration the fact sand settles out of manure when diluted (some even settles when undiluted) as well as use of equipment not intended or designed for sand.

Sadly, the predominant reason for producers not using sand bedding is fear of manure handling. Industries such as mining and domestic sewage treatment both handle sand.

Adopting design methodologies and equipment from these industries can result in favourable outcomes when it comes to sand bedding both from cow comfort and producer comfort (manure handling) standpoints.  PD

References omitted due to space but are available upon request. Click here to email an editor.

Andrew Wedel PE

LATEST BLOG

LATEST NEWS